Lbl-lighting MO Direct Feed Surf Elec Xfmr 300 w 120v/12v Manuel d'utilisateur télécharger pdf

Installation Instructions for

12 Volt 150 & 300 Watt Single Direct Power

Feed Electronic Surface Mount Transformers

1.2

TRANSDIR-SFE_

980MRLDSFESMT

GP I :ENERAL RODUCT NFORMATION

This instruction is for the following models:

150 Watt Single Direct Power Feed Electronic Surface Mount

Transformer (TRANSDIR-SFE150-_)

300 Watt Single Direct Power Feed Electronic Surface Mount

Transformer (TRANSDIR-SFE300-_)

This product is ETL listed only when all the products used are

supplied by LBL Lighting, is suitable only for indoor dry locations

and approved for use at any height above the finished floor.

A typical installation is shown. Specific installation must be in

accordance with local electrical codes.

This product may be dimmed only with a low voltage electronic

dimmer. Using a dimmer not designed for low voltage electronic

applications may cause undesirable noise and potentially shorten

the life of the transformer.

This product is intended for use with LBL Lighting low voltage

lighting systems only.

Read all instructions thoroughly. Read "Important Safety

Information" on next column before proceeding with the

installation.

Important Safety Information

Do not conceal or extend bus bar conductors through a building

wall.

Do not install this lighting system in a damp or wet location.

To reduce the risk of fire and burns, do not install this lighting

system where the uninsulated open bus bar conductors can be

shorted or contact any conductive materials.

To reduce the risk of the system overheating and possibly causing a

fire, make sure all the connections are tight.

Do not install fixture assemblies closer than six inches to curtains

or similarly combustible materials.

Turn the electrical power off before modifying the lighting system in

any way.

The fixtures used with the system must be identified to be used

with the corresponding system.

Minimum volume of the electrical box must be 6 cubic inches (98

cubic centimeters).

Load the circuit of the surface mount transformer to no more than

the maximum rated capacity as specified.

To reset the electronic surface mount transformer, turn the power

off then on (main power, breaker panel, or wall switch).

Monorail

CAUTION - RISK OF FIRE

This product must be installed in accordance with

the applicable installation code by a person familiar

with the construction and operation of the product

and the hazards involved.

Use minimum 90°c supply conductors.

1 2 3 4

Résumé du contenu

Page 1 - Important Safety Information

Installation Instructions for12 Volt 150 & 300 Watt Single Direct PowerFeed Electronic Surface Mount Transformers1.2TRANSDIR-SFE_980MRLDSFESMT1GP

Page 2 - Install the Transformer

2Install the TransformerCROSSBAR#8-32 FLATHEAD SCREWRemove the two #8-32 flat head screws to remove thecrossbar.#8-32SCREWCROSSBARMount the crossbar t

Page 3 - 1A2A 1A2C

3Connect the Monorail to TransformerRemove the power feed cap from the power feed housing.Completely back out the screw on the power feed cap.POWER FE

Page 4 - SAVETHESE INSTRUCTIONS!

Commentaires sur ces manuels

Pas de commentaire

Lbl-lighting MO Direct Feed Surf Elec Xfmr 300 w 120v/12v Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Éclairage Lbl-lighting MO Direct Feed Surf Elec Xfmr 300 w 120v/12v. LBL Lighting MO Direct Feed Surf Elec Xfmr 300 w 120v/12v User Manual [de] Manuel d'utilisatio

Résumé du contenu

Commentaires sur ces manuels

Produits connexes et manuels pour Éclairage Lbl-lighting MO Direct Feed Surf Elec Xfmr 300 w 120v/12v